GMA-DP Series Profibus-DP Interface Bus-based Absolute Encoder
1. Main Product Parameters and Technical Data
Category | Parameter | Value/Description |
---|---|---|
Basic Information | Series/Model | GMA-DP Series encoder |
Encoder Type | Profibus-DP interface multi-turn absolute encoder | |
Total Resolution | Up to 29 bits (Note: Some descriptions mention “Multi-turn Max. 12 bits, Single-turn Max. 13 bits”, while later “Max. 16 bits for single turn, Total Max. 29 bits”) | |
Housing Diameter | 58 mm | |
Solid/Hollow Shaft Diameter | 10 mm | |
Supply Voltage | 5V and 8–29V (depending on the version) | |
Interface | Profibus-DP | |
Electrical Data | Resolution | Single turn: up to 16 bits; Total resolution: up to 29 bits |
Maximum Frequency Response | 30 kHz | |
Power Supply Voltage | 8–29 V (Note: some descriptions also mention a 5V version) | |
Mechanical Data | Starting Torque | 0.01 N·m |
Maximum Axial Load | 5–30 N | |
Maximum Radial Load | 10–20 N | |
Maximum Rotational Speed | 6000 rpm | |
Weight | 160–200 g | |
Environmental Data | Operating Temperature | -30 °C to 80 °C |
Storage Temperature | -40 °C to 80 °C | |
Protection Rating | IP65 | |
Certifications | CE, ROHS, KC, ISO9001 | |
Packaging | Standard export packaging or as specified by the buyer | |
Delivery Lead Time | Ships within one week after full payment (Samples in 3 days, mass production in 7–10 days) |
2. Installation and Wiring Precautions
Mechanical Connection
It is recommended to use an elastic soft coupling between the encoder shaft and the user’s output shaft to avoid damage to the encoder’s shaft system due to misalignment or runout.
Pay attention to the allowable axial load during installation.
Ensure that the difference in axial position between the encoder shaft and the user output shaft is no more than 0.20 mm, and the deviation angle of the axes is less than 1.5°.
Avoid knocking or dropping the encoder during installation.
Electrical Wiring
Do not reverse the power and ground wires.
The ground wire should be as thick as possible (generally larger than φ 3).
Do not allow the encoder output wires to overlap each other to prevent damage to the output circuitry.
The signal lines should not be connected to a DC or AC power supply to avoid damage.
The motor and other equipment connected to the encoder must be well-grounded to prevent static electricity interference.
Use shielded cables for wiring, and check all connections carefully before starting the machine.
For long-distance transmission, consider signal attenuation and choose an output mode with low output impedance and strong anti-interference capability.
Avoid using the encoder in environments with strong electromagnetic interference.
3. Application Fields and Product Features
Item | Description |
---|---|
Application Fields | Automatic control and measurement systems in machinery manufacturing, shipping, textiles, printing, aviation, military, testing machines, elevators, etc. |
Product Features | Vibration-resistant, corrosion-resistant, pollution-resistant |
4. Encoder Selection Guidelines
Brand Replacement Advice
If you have used encoders from other brands, please provide their brand and model information. Our engineers will advise you on a high cost-performance equivalent replacement.Determine the Encoder Type
Choose the appropriate type for your application:Manual Pulse Generator
Select the Output Format/Interface
For incremental encoders: choose NPN, PNP, Line Driver, Push-Pull, etc.
Or select the required interface (e.g., Parallel, SSI, BISS, Modbus, CANopen, Profibus, DeviceNET, Profinet, EtherCAT, Power Link, Modbus TCP)
Determine the Resolution
Gertech incremental encoders: up to 50,000 ppr
Gertech absolute encoders: up to 29 bits
Determine the Dimensions
Choose the required housing diameter and shaft diameter (for example, this product has a 58 mm housing and 10 mm shaft diameter)
5. Equivalent Replacement Product Information
Omron Equivalent Models:
E6A2-CS3C, E6A2-CS3E, E6A2-CS5C, E6A2-CW3C, E6A2-CW3E, E6A2-CW5C, E6A2-CWZ3C, E6A2-CWZ3E, E6A2-CWZ5C;
E6B2-CS3C, E6B2-CS3E, E6B2-CS5C, E6A2-CS5C, E6B2-CW3C, E6B2-CW3E, E6B2-CW5C, E6B2-CWZ3C, E6B2-CWZ3E, E6B2-CBZ5C;
E6C2-CS3C, E6C2-CS3E, E6C2-CS5C, E6C2-CW3C, E6C2-CW3E, E6C2-CW5C, E6C2-CWZ3C, E6C2-CWZ3E, E6C2-CBZ5CKoyo Equivalent Models:
TRD-MX, TRD-2E/1EH, TRD-2T, TRD-2TH, TRD-S, TRD-SH, TRD-N, TRD-NH, TRD-J, TRD-GK, TRD-CH seriesAutonics Equivalent Models:
E30S, E40S, E40H, E50S, E50H, E60S, E60H series
6. FAQ (Frequently Asked Questions)
How to select an encoder?
Determine the type of encoder needed (incremental or absolute) according to your application requirements, and then contact the sales service department for detailed assistance.
What specifications are required before placing an order?
Encoder Type (solid shaft or hollow shaft)
Housing Diameter (minimum 25 mm to maximum 100 mm)
Shaft Diameter (minimum 4 mm to maximum 45 mm)
Phases & Resolution (minimum 20 ppr, maximum 65,536 ppr)
Circuit Output Mode (choose from NPN, PNP, voltage, push-pull, line driver, etc.)
Power Supply Voltage (DC 5V–30V)
How to choose the right encoder on your own?
Confirm your application’s requirements, check the installation dimensions, and contact the supplier for more details.
What is the minimum order quantity (MOQ)?
The MOQ is 20 pcs (smaller quantities are acceptable but may incur higher freight charges).
Why choose Gertech brand encoders?
All encoders have been designed and developed by our own engineering team since 2004. Most electronic components are imported. We own an anti-static, dust-free workshop and our products have passed ISO9001 certification. Quality is our culture.
What is the lead time?
Samples: 3 days; Mass production: 7–10 days.
What is the warranty and technical support policy?
1-year warranty and lifelong technical support.
What are the benefits of becoming an agency?
Special pricing, market protection, and comprehensive support.
What is the process to become a Gertech agency?
Please send your inquiry, and we will contact you as soon as possible.
What is the production capacity?
We produce 5000 pcs per week and are currently building a second-phase production line.